Bleeding brakes after a change of pads is not an uncommon problem, and there are many ways to fix it. The most common cause of bleeding brakes is when the old pad was still on the rotor, or when new brake fluid got inside the caliper where it can’t escape.
There are several steps you need to take in order to fix your car: remove all debris from around the calipers, bleed them properly with brake fluid (or DOT 3 if your car has that option), replace any worn parts, and finally put everything back together correctly.
If at any point during this process you notice more braking problems than usual, take your car into a certified mechanic for further inspection and repair work.
Contents
Should You Bleed Brakes After Changing Pads
Bleeding the brakes after changing pads is a common safety precaution you should take to avoid any potential accidents. When bleeding your brakes, be sure not to over-bleed them as this could result in brake failure.
Follow the manufacturer’s instructions when bleeding your brakes and make sure all of the fluid has been removed from the system before re-installing your pads or discs.
If you notice uneven braking, it may be time to bleed your brakes again; otherwise, there is a chance that they will wear out prematurely due to lack of proper lubrication.
How To Bleed Your Brakes
If you have to brake suddenly, your car’s brakes may not work as well as they should. This is because when the brakes are applied, their pistons push on the pads which in turn create a friction against the wheel.
To make sure that your car has enough braking power and that it will stop quickly in an emergency situation, it is important to bleed the brakes every few months or whenever there is a change in fluid levels.
Check Your Brake Fluid Level
Make sure that your brake fluid level is full and correct. If the fluid’s level falls below the minimum line on your reservoir, it’s time to add more fluid.
Remove The Brake Hoses from The Wheel Cylinder
Now you’ll need to remove both of the brake hose clamps from the wheel cylinder (the parts attached to each end of the brake hoses).
You may need a wrench or pliers for this job depending on what type of clamping device was used when installing your brakes.
Bleed The Brakes
Once you have removed both hose clamps and freed up both ends of each brake hose, pump them full of air until they start bleeding (you’ll see bubbles coming out).
Next, use a standard garden siphon to extract all the old fluid from each hose while simultaneously filling them with new brake fluid using a Schrader valve or other suitable container.
Be careful not to overfill either hose. Replacing too much old fluid with new will only cause problems down the road.
Maintenance After Installing New Brake Pads
After installing new brake pads, it’s important to keep them in good condition by performing regular maintenance.
This includes checking the brakes for leaks and replacing any parts that need attention.
Make Sure Your Brake Pads Are Properly Seated
It is important that the brake pads are properly seated on the rotor to ensure proper braking performance.
If they are not in the correct position, this can cause poor stopping power and increased wear on your brakes. Note that driving on worn brake pads isn’t safe.
Check Your Brake Fluid Level and Add More if Necessary
If you notice a decrease in braking effectiveness or an increase in noise when driving, it may be time to check your fluid levels and add more if necessary.
Over-dosing can also result in corrosion of parts within the system, so always consult with a mechanic before making any changes to your car’s fluids.
Clean Your Brake Pads and Rotors with a Brake Cleaner and a Soft Cloth
To clean off accumulated debris from inside the pad or rotor surface, use a mild soap mixed with water along with some rubbing alcohol or degreaser.
For tougher dirt buildup, use a brake cleaner specifically formulated for cleaning brakes (such as Meguiar’s Xtreme Brake Cleaner).
How to Reset Brakes After Changing Pads
In order to reset your brakes, you need to take a few steps.
- First, you will need to find out how many miles per hour your car goes before it starts slowing down.
- Next, you will need to find out how many feet your car goes before coming to a complete stop.
- Lastly, you will have to find out where the brake pedal is located on your vehicle and press it in order for the brake pedal arm and cable lever arm on your vehicle’s brake pedal assembly (which is attached by a cable) to move back into position and reset the brakes.
FAQs
How Many Times Do You Need to Pump the Brakes After a Pad Change?
It depends on your car’s braking system. If your car has a drum brake system, you would need to pump the brakes four times after changing a brake pad.
Can You Bleed Abs Brakes Without a Scan Tool?
If you have a lot of experience with cars, the answer is yes. If you are a novice, the answer is no.
Do You Open Brake Fluid Reservoir When Bleeding Brakes?
In order to bleed brakes, you need to open the brake fluid reservoir. Brakes are typically found on the front of the vehicle.
How Much Does It Cost to Bleed Brakes?
According to estimates, it costs $80-100 to replace all four brake pads and rotors on a vehicle.
Conclusion
If you have recently changed your brake pads, it is always a good idea to bleed the brake system.
Bleeding will clear any air bubbles and prevent them from causing future problems with your brakes.
Make sure to refer to your car’s owner’s manual for specific instructions on how to bleed the brakes system.
Always be careful when bleeding the brakes as failure can result in serious injury or even death. After bleeding your brakes, make sure they are properly lubricated so that they function at their best and avoid accidents in the future.