How To Change Brake Pads on Lexus GS 350?

If you need to change brake pads on your Lexus GS 350, here is how to do it: Park the car in a level place and turn off the ignition Locate the four screws that hold down the caliper cover Remove these screws and then slide out the caliper cover.

You will now see two brake pads mounted on either side of an actuator rod to remove one pad, use a flathead screwdriver to pry up on one end of the actuator rod until it pops off Repeat this step for the other pad- be careful not to damage or bend any parts during removal.

Once both brakes have been replaced, reattach everything using new screws and replace the actuator rod.

Brake Pads on Lexus GS 350

Brake pads are essential for safety when driving a Lexus GS 350. Make sure to replace your brake pads regularly to ensure proper braking performance and prevent wear on the disc brakes.

Replace your brake pads before they become too worn or damaged, as this could cause them to fail later on down the road. 

To find out if you need new brake pads, simply press down lightly on each pad with your finger while rotating it around its axis – if there is any resistance then you likely need new ones. 

If you do not have time to replace your entire set of brake pads at once, consider replacing just one or two at a time so that the discs don’t overheat and prematurely wear out their surfaces.

How To Change Brake Pads on Lexus GS 350

If you’re looking to change your brake pads on your Lexus GS 350, follow these simple steps:

Changing brake pads on a Lexus GS 350 is a fairly straightforward process, but there are a few important things to keep in mind. 

First, make sure that the car is level and secure before starting. 

Second, use caution when working with the brakes – they can be very powerful. 

Finally, replace the brake pads exactly as specified by your car’s manufacturer – otherwise, you may end up with problems down the road.

Verify that the car has a functioning parking brake

If you have to replace your brake pads, it is important to make sure that the parking brake is working properly before starting any work. 

To do this, first, verify that the car has a functioning parking brake by checking for leaks around the calipers or pressure sensors. If everything looks good, then you can proceed with replacing the pads.

Park the car in a safe place and turn off the engine

Once you know that your brakes are functional, it’s time to park your Lexus GS 350 safely so you don’t accidentally hit anything while working on it. 

Next, disconnect both battery cables and remove both wheel covers before raising both suspension arms into position using a jack or hoist.

Remove the wheel covers

After turning off all of the vehicle’s accessories and securing them away safely, it’s time to take off those pesky wheel covers. Use a screwdriver or wrench to unscrew them from their mountings and set them aside somewhere safe.

Disconnecting the negative battery cable

Now we will start removing some of these big bolts holding down our steering column assembly: first, we need to disconnect the negative battery cable at lug nut 10 (just below the driver-side front tire). 

Again, use caution as there are many wires tucked up under here.

Raise both suspension arms into position using a jack or hoist

After taking care of steps 3-4 above, now it’s time to raise those two hefty pieces of equipment using either an adjustable ladder jack OR an industrial-grade hydraulic arm lift such as this one: 

Be careful not to strain too much on any components during these steps – if done correctly they should just “click” into place once raised.

Remove the Screws That Hold on the Brake Pads

First, you will need to remove the screws that hold on the brake pads. You can do this by removing the two bolts that are located near each wheel hub.

Once these bolts have been removed, you can carefully pull off the brake pads.

Pry off Old Pads

Once the brakes have been removed, you will need to pry off old pads from both rotors using a flathead screwdriver or a hammer and chisel. Be very careful not to damage any of your rotor surfaces while doing this.

Install New Brake Pad Sets onto Rotors

Finally, it is time to install new brake pad sets onto your rotors. To do this, simply place one set of pads over each rotor and tighten down all of the mounting screws until they are secure.

Make sure not to overtighten these screws as Overturning or damaging your rotors could lead to serious safety concerns.

Test Drive to Check Out that New Brake Pads are Functioning Properly

After you replace your brake pads, it is important to test them out first.

You can do this by driving the car around for a while and making sure that the brakes feel responsive and sturdy when you press on them.

Signs of Bad Brake Pads That Need to Be Changed

It is not safe to drive with worn brake pads. If you notice any of the following signs, it means that your brake pads need to be replaced:

Peel Them Off of Rotors

Now it is time to peel old pads away from your rotors using a pair of pliers or your fingers.

Make sure that you use enough pressure when peeling them so that they don’t come off in small pieces – this could lead to problems with braking performance later on down the road.

The Vehicle Won’t Start

If your brake pads are worn down, the vehicle may not start. This is because the brakes will not have enough power to stop the car. 

When this happens, you will likely hear grinding noise when you try to start the engine.

Hard To Stop on Reducing Speed

When your brake pads are worn down, they don’t provide as much resistance when reducing speed or stopping on a hill. This can make it difficult to stop at a reduced speed or in an emergency situation.

Slower Speeds Than Normal

If your brakes aren’t working correctly, you might experience slower speeds than normal while driving around town or on long trips outside of town limits.

Brakes Feel Soft or Floppy When Applied

When your pads lose their friction ability over time, they will feel soft and floppy when applied to the rotor disk (or drum). 

You may also notice that braking distances become longer when applying pressure to the pedal at low speeds.

Noise Coming From The Rotors And/Or Calipers

If there is excessive wear and tear on either of these components – especially if it affects how well they work together – then you might hear abnormal noises coming from them while braking: 

Clunking sounds during deceleration and screeching noises during acceleration; of which could be indications that replacement is necessary for both parts.

Pads Are Diminished in Color

After being wetted down with brake cleaner Many times, pad deterioration caused by road salt or other chemicals can be reversed by cleaning them with brake cleaner before putting new pads in.

Pad Wear Appears as Small Circles On Rotors

Although most people think that wearing out pads causes circles-like impressions on rotors called “brake dust,” actually what’s happening is that grit has worked its way into between pad grooves and onto rotating surfaces where it becomes embedded.

FAQs

How Much Are Brake Pads for Lexus GS350?

Brake pads for the Lexus GS350 are typically priced in the range of $283 – $309.

Is It Easy to Replace Your Own Brake Pads?

Replacing brake pads is relatively easy, depending on the make and model of your car.

Do You Need to Bleed Brakes When Changing Pads?

If you are changing pads on a car with disc brakes, you will need to bleed the brakes.

Can I Replace Brake Pads and Rotors Myself?

Brake pads and rotors can be replaced by yourself, but it is a job that requires some skill and knowledge. It is not a difficult task, but it is one that you should not try if you are not familiar with the process.

What Happens if You Replace Brake Pads Without Turning the Rotors?

If you replace the brake pads without turning the rotors, your car will not be able to brake as well.

How Long Does Changing Brake Pads Take?

Generally, it takes around 4 hours to change brake pads.

To Recap

Change your brake pads on a Lexus GS 350 if they show any signs of wear or damage. Use the right tools and follow the manufacturer’s instructions to change your pads correctly and safely. 

A regular brake pad change will help keep your car in good condition, reduce noise, and prolong its life. 

If you have severe braking problems or notice significant fading or wearing on your brakes, it is time for a new set of pads altogether.