How to Change Brake Pads on Jeep Patriot?

Changing brake pads on your Jeep Patriot is an easy task that can be done in just a few minutes. The best way to do this is by removing the wheel and taking off the drum brakes. 

After you’ve removed the drums, use a wrench to loosen each pad bolt and pull it out of its retaining bracket. Replace the new pads with fresh ones, making sure they are properly installed into their brackets before tightening them back down using the bolts provided. 

Be sure to lubricate all moving parts with an anti-seize compound prior to performing this task so that everything operates smoothly and there are no issues down the road.

Brake Pads on Jeep Patriot

Brake pads are an important part of your car, and they’re especially crucial on a Jeep Patriot. It’s important to replace brake pads regularly so you can avoid costly repairs or accidents. 

Make sure the brakes feel firm and not spongy when you press them down with your fingers – this means the pads have worn out.

If you think your brakes need replacing, take them in for inspection as soon as possible to ensure that everything is set correctly before making any expensive decisions about repair work. 

When shopping for new brake pads, be sure to read the reviews so you know what other drivers are saying about which brands and sizes offer the best performance.

Needed Tools to Change Brake Pads on Jeep Patriot

If you’re looking for the tools needed to change your brake pads on a Jeep Patriot, you’ll need an impact wrench, ratchet and socket set, and some old towels. 

Check your owner’s manual for specific instructions on how to do this task.

• Jack
• Tire iron
• Lug wrench
• Flathead screwdriver 
• Torx bit 
• Brake pads 
• Toolbox 
• Hammer

How To Change Brake Pads on Jeep Patriot

If you’ve ever needed to replace the brake pads on your Jeep Patriot, then you’ll know that doing so requires a few different tools. In this article, we’ll list all of the tools you need and explain how to use them.

If you’re looking to fix or replace your Jeep Patriot’s brake pads, there are a few steps involved. First, remove the wheel and tire. 

Then, use a jack to raise the car off of the ground. Finally, access the brakes from underneath by removing bolts and screws.

Park the Jeep Patriot in a safe place

Before you start working on your car, make sure that you park it in a safe place. This will help to avoid any accidents while you’re working on your car.

Remove the driver’s side door panel

Next, remove the driver’s side door panel by unscrewing the three bolts located near the hinge. Be careful not to damage the plastic trim around the edge of the window.

Locate and remove front-wheel drive assembly

Once you’ve removed the door panel, locate and remove the front wheel drive assembly by disconnecting all six mounting screws located along its length. Make sure that you keep track of which screw goes where so that it can be reassembled correctly later on.

Disconnect and remove brake pedal cable mountings

Now that front-wheel drive is out of commission, we need to take care of disabling those pesky brake pedals. 

First, loosen each bolt securing each brake pad foot to its mounting bracket using a 2mm hex key wrench (or equivalent). 

Next, simply lift up on each brake pedal until they detach from their respective mounts and then move them away from the vehicle for easier access later on when reinstalling them.

Clean all dirt grease etc

After removing everything from underneath your Jeep Patriot’s hood, it’s time for us to clean everything down before we try installing our new brake pads again. 

We’ll start off by cleaning all debris off of every bolt with an appropriate cleaner such as PB Blaster. 

Afterward, use a lint-free cloth soaked in rubbing alcohol (90%)to wipe down every surface inside and outside of wheel wells

Get A Jack

A jack is a key tool that you will need to change your brake pads on your Jeep Patriot. A jack can be used to raise the car off the ground, which makes it easier to work under the vehicle and remove the old pads and install the new ones.

Have Some Supplies Ready

Before you start working on your Jeep Patriot, make sure that you have some supplies ready including a Phillips head screwdriver, ratchet set, socket wrench set, and replacement brake pad kit (if needed).

Locate The Brake Pads on Your Vehicle

To change the brakes on your Jeep Patriot, first, locate them in relation to the wheel hub. Once you know where they are located, use a Phillips head screwdriver to unscrew each lug from its mounting bracket using a ratchet set.

Make sure not to over-tighten as this could damage your Hub or Wheel Bearings.

Remove The Old Brakes Pads

Once both lugs are removed from their brackets using a Phillips head screwdriver, it’s time to remove the old braking pads by gently prying them away with a Socket Wrench Set. Be careful not to damage either of these parts in any way.

Install The New Braking Pad Kits If Needed

If replacing all of your brake pads at once isn’t an option for whatever reason then simply install one complete kit’s worth of new brakes by reversing steps 3-4 above – just remember: 

Always replace ALL four caliper pistons AND hoses when changing brake pads. Failure To Do So Can Result in Serious Injury Or Damage.

FAQs

How Much Does It Cost to Replace Brakes on a Jeep Patriot?

The cost to replace brakes on a Jeep Patriot ranges from $189 to $203.

How Long Do Brake Pads Last Jeep Patriot?

The average Jeep Patriot brake pads will last about 30,000 miles, and the pads will usually last about 70,000 miles before getting crack on it.

Is Jeep Patriot a reliable car?

Yes, the Jeep Patriot is a reliable car.

What is the biggest problem with Jeep Patriot?

The biggest problem with the Jeep Patriot is that it is prone to TIPM (thermal interlock protection module) failure and water leaks.

Are Duralast Max Brake Pads Good?

The Duralast Max brake pads are cheaper but better for their price range.

Final Thought

Changing brake pads on your Jeep Patriot can be a daunting task, but with the right tools and advice, it’s easy to do. 

Make sure you have all of the necessary parts before starting – this includes the correct socket set for your vehicle and a jack or lift device if needed. Be patient as you work – changing brake pads is an important job that should not be rushed. 

Follow these steps in order: remove the old pads, put in new ones, and then reinstall everything correctly. 

If you follow these tips, your Jeep Patriot will stop safely and efficiently once again.