If your brake pads are worn down, it is time to change them. The 2010 Chevy Impala has a standard 12-volt system and the procedure is generally the same for all models of cars.
Remove the wheels and jack up the car–the brakes should be off–so you can get at the front end easily. Disconnecting and removing four clips will release the calipers from their brackets on each rotor (two per side).
Locate new brake pads and place them in position over both rotors, making sure they are correctly aligned with grooves in caliper brackets (they need to be slightly shorter than the original pad dimensions).
Clean off any grease or dirt that may have accumulated between rotor and pad during installation, then replace clip screws securely back into place.
Contents
Brake Pads on 2010 Chevy Impala
If your 2010 Chevy Impala’s brake pads are wearing out, you may need to replace them soon. The wear on a car’s brake pads can be monitored by checking the pad compound level and/or bleeding the brakes if there is excessive dust or debris on the rotor or caliper.
There are several factors that affect how often brake pads will need to be replaced, including driving habits, climate conditions, and vehicle maintenance schedule.
When replacing brake pads, it’s important to use genuine GM parts for optimum performance and longevity of your braking system. In most cases, stopping distances won’t change significantly after installing new brakes; however they may feel stronger initially due to bedding-in effect.
Required Tools for Changing Brake Pads on 2010 Chevy Impala
When it comes to changing brake pads on a 2010 Chevy Impala, you’ll need the following tools:
Jack
Your car needs a jack in order to lift the vehicle off of its wheels. A jack can be used for a variety of tasks including changing brake pads or tires.
Crowbar/Hammer
A crowbar or hammer is necessary for breaking open the bolts that hold the brake pads on your 2010 Chevy Impala in place.
Torque Wrench
A torque wrench is a must-have tool for any mechanic. It’s used to tighten or loosen bolts and screws.
If you need to remove any stubborn bolts, locking pliers or wrench set are essential tools for the job. They allow you to grip onto objects tightly while turning them with a wrench or socket tool.
Screwdriver
Another important tool you will need is a Phillips head screwdriver. This type of screwdriver has a sharp, pointed end that helps you remove screws easily and quickly.
Brake Pad Tool
The brake pad tool is designed specifically for removing brake pads on the 2010 Chevy Impala.
With this tool in hand, it’s easy to remove and replace the pads without hassle or damage to your car’s engine or other parts.
Socket Set & Ratchet set
If you plan on doing more than just changing the brake pads on your 2010 Chevy Impala, then an 8-inch socket set and 1/2-inch ratchet set will come in handy.
These tools allow you to spin bolts securely while providing enough leverage so that they can be removed without too much effort.
Safety Glasses
When working on your car, it is always important to wear safety glasses. This will protect you from possible injuries if something goes wrong and you are not careful.
How To Change Brake Pads on 2010 Chevy Impala
If you are experiencing a lot of vibration or noise when you brake, it may be time to replace your brake pads. This guide will show you how to do this on a 2010 Chevy Impala.
If you’re looking to replace the brake pads on your 2010 Chevy Impala, this guide will show you how to do it step by step.
Locate and remove the emergency brake handle
The first step in changing your brake pads is locating and removing the emergency brake handle.
This can be done by gently pulling on either side of the handle to release it from its mounting location.
Remove the screws
Next, you will need to unscrew each screw that holds the brake pad onto the disc. You should do this in reverse order so that you have access to all four screws once they are removed.
Once all of these screws are loose, you can easily remove your old brake pads and replace them with new ones.
Inspect each brake pad
After installing your new brakes, it is important to inspect them carefully for any damages or wear before reattaching them to their respective discs.
Make sure that there are no tears or gouges present on your pads before reinstalling them onto your car’s rotors.
Grasp each side of the brake pad
To change your brake pads, you first need to grasp each side of the brake pad and install them onto the discs in the correct orientation.
Make sure that you use new screws in reverse order so that everything is properly aligned when you’re finished.
Install new brake pads onto discs
After grasping each side of the brake pad, it’s time to install them onto your disc brakes by aligning it with one screw and then tightening down using a wrench or Allen key.
Be sure not to over-tighten these screws as this can damage your brakes prematurely.
Replace screws in reverse order
Once you’ve installed all four pads, replace any missing or damaged screws with replacements before driving your car for long distances again to make sure everything works correctly.
Test drive your car to ensure proper function
Make sure that the brake pads are working properly before you begin any work on them. A loose or faulty brake pad can cause a lot of problems, including making it difficult to stop the car quickly.
Additionally, if the brakes aren’t functioning correctly, this could lead to an accident.
FAQs
Is Chevy Impala a Good Car?
The 2010 Chevy Impala is a great car that does most things well inside the cabin and on the road.
What Problems Do Chevy Impalas Have?
Chevy Impalas have been around for over 50 years and are still a popular car choice among people in the US.
However, there have been some problems with these cars in including engine failures and transmission issues.
What Year Did They Stop Making Chevy Impalas?
The Chevy Impala ceased production in 2020.
What’s Better Impala or Malibu?
Though it depends on the individual buyer’s needs and preferences, Impala is better in case of larger passenger and cargo capacity.
What Replaced the Chevy Impala?
The Chevy Impala was replaced by the GMC Hummer EV.
Is There a 2021 Chevy Impala?
No, there is not a 2021 Chevy Impala.
Do Impalas have rear brakes?
Yes, impalas do have rear brakes.
How To Change Brake Pads on 1996 Chevy Silverado
To change brake pads on a 1996 Chevy Silverado, remove the wheel and tire. Remove the two screws that hold the brake caliper in place.
Remove the brake caliper. Rotate the wheel so you can see the pads. Remove the old brake pads by pulling them off the rotor.
To Recap
Brake pads on a 2010 Chevy Impala can be replaced in several ways, depending on the severity of the damage done. The most common way to replace brake pads is by using a kit from your dealership or mechanic.
If you don’t have access to either of these options and the pads are severely worn down, you may be able to replace them yourself with some basic tools and knowledge about how brakes work.
If replacement isn’t an option or if your car doesn’t come with factory-installed pads, then it’s important to get new brake shoes installed as well so that braking power is restored as much as possible.
Always consult with a mechanic before making any changes to your car’s braking system; improper installation could lead to serious injury or worse.